Plumbing 101: What You Must Have for Installing a Bathtub
Plumbing 101: What You Must Have for Installing a Bathtub
Blog Article
The article author is making several good points relating to Installing A Bathtub overall in the content on the next paragraphs.
Setting up a tub isn't exactly brain surgery, yet it does need solid plumbing, carpentry, and also often, tiling skills. Replacing an old bath tub with a new one is additionally a reasonably challenging task. If the old tub is readily obtainable, the job can move quickly; if you have to open a wall surface to remove the old tub as well as position the new bath tub, the job is much harder. In either instance, the project is within a house handyman's skills, although you will require an assistant to leave the old bathtub as well as set in the new one. See to it you have actually certified yourself for the task and are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed job, it is better to consider employing one before you begin. Chances are you might need an expert plumber to make tube links.
This post will certainly aid you mount a new bathtub in your bathroom if you have actually currently gotten a new tub and also do not need to alter the setup of your previous water supply pipelines.
Your tools and also material checklist need to comprise the following:
Preparing for the Installment
Firstly, the supporting frame provided with the bathroom must be fitted (if needed) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps device to stop stress on the tub.
Fit the flexible tap ports to the bottom of the two faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last setting.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you need to do is separate the water system. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been removed, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any old sealing substance.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, put the tub in the called for placement. The wood boards are useful in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level as well as adjusting the feet on the tub up until the spirit level checks out level.
To mount taps, fit all-time low of the furthest versatile faucet port to the ideal supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Switch on the supply of water and also examine all joints and also new pipework for leakages and tighten them if needed. Fill up the bathtub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, fix the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has been used a minimum of once as this will settle it into its final setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washers remain in location in between the faucet and the sink. Safeguard the tap in position with the manufacturer provided backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet adapters. The previous type ought to be connected to the faucet finishes first, tightening only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to penetrate the wall in between the bath as well as the tiling, leading to complications with moisture and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes as well as cartridges, as well as can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealer can crack fairly early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the marketplace. It is a good idea to fit the tiles making use of waterproof or water-proof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic person who reads about How to Install a Bathtub Yourself, I was thinking sharing that excerpt was a great idea. Liked our blog? Please share it. Let others locate it. Thanks for going through it.
Need help? Call. Report this page