Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
In this article down the page you might get additional incredibly good details all about Tools You Need to Install a New Bathtub .
Mounting a bathtub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably tough job. If the old bathtub is readily accessible, the job can relocate easily; if you have to open up a wall to get rid of the old tub as well as position the brand-new bath tub, the task is much harder. In either case, the job is within a home handyman's abilities, although you will require a helper to vacate the old bathtub and also embeded in the brand-new one. Make sure you have actually qualified yourself for the task as well as fit trying it. As opposed to working with a specialist to take over a halfway-completed project, it is much better to think about utilizing one before you start. Possibilities are you might need a professional plumber to make tube connections.
This write-up will aid you set up a brand-new bathtub in your shower room if you have actually currently gotten a new bathtub and also don't require to change the setup of your previous water supply pipelines.
Your tools as well as material checklist should consist of the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, turn on the faucets to drain any water staying in the system. The procedure of removing the existing faucets can be rather troublesome as a result of the restricted access that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth all set for the remaining water that will originate from the pipes. Once the supply pipelines have actually been gotten rid of, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Prior to carrying on to fit the new taps, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin making sure that the washers are in area in between the tap and also the sink. Safeguard the faucet in place with the producer given backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal tap connectors. The previous type ought to be linked to the tap finishes first, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Utilizing the two wooden boards under its feet, position the bathtub in the needed setting. The wood boards are useful in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the level and also adjusting the feet on the bathtub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression join; then do the same for the other tap.
Switch on the water and inspect all joints as well as brand-new pipework for leakages and also tighten them if needed. Load the tub as well as additionally inspect the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the bath tub should wait up until the bathtub has been used at the very least once as this will certainly settle it right into its last position.
Preparing for the Installation
First of all, the supporting frame provided with the bath should be fitted (if needed) according to the producer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make sure that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to prevent pressure on the bathtub.
Fit the versatile tap adapters to the bottom of both taps utilizing 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its last placement.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, leading to problems with moisture and possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bath tub with water before securing, to permit the activity experienced when the tub is in usage. The sealant can split fairly very early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly available on the market. It is a good idea to fit the floor tiles utilizing waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very drawn to How to Install a Bathtub Yourself and I hope you enjoyed reading our piece. So long as you liked our page kindly don't forget to share it. We take joy in reading our article about How to Install a Bathtub.
Book Inspection Report this page